I'm up and could be ready in 30 min

found some frames on the island cheap http://www.pinkbike.com/buysell/1080488/
http://www.pinkbike.com/buysell/892535/
http://www.pinkbike.com/buysell/1057281/

Have fun. Been a whole year now since I was at the park. Hope to get up a few times this summer sucks renting though. Next summer the bike will be done though. Then I will be going a lot more

Haha like me. When the caps down I grab the 20" . No slope bike anymore. Should have kept it.

Hitting it up over the weekend eh? This weekend only going to build. Don't think my hand will be stable enough to ride

Yeah can do qr too because of the recess in the drop out

435

Taking my nefew

Ill be there tomorrow at about 11 am

Yo how was the park today

YA CAlled him yesterday

hahaha for sure! protection is recommended for that one

Yeah, I knew it was a joke, no hard feelings, eh?

no worries man, sorry for my MANstruation

np man

i use a 8 mm

they all use the same bolts on the female Thats what Quin told me as he stumbled out of my reck room haha.

http://profileracing.com/ht_hubohaul2.php

no problem

Its eitherna 7/8 or an 8 mm according to the overhaul section on their sight . Hope that helps

Nate got me trippin with profile when i was going to get madera hubs .i was like f*ck this and got the g sport. I think profile actually suplies the part with the hex wrench . So it sucks if you are the second owner and the original owner does not give you the tool :/. I wanted ti bolts for my ratchet and they were sold out . But what they did have were a f*ckload of profile ti spec bolts go figure pffft ,lol

Yeah iv seen them not kept up very well

Profile kills me haha . I reworked my freinds cranks today at the park after he was complaining about that he installed a new animal bb and it was working shitty . Me and Quin were going nuts looking through hex wrenches. Turned out it used imperial and metric

absolutely awesome, little weird at 1st because the rear's shorter than the pimp, but I'm loving it!!!

He is not coming ill meet you there

Kooooool

Ya I justdrove by the park and some of it was dry. I'm gonna drive there cause I have to get my daughter by 2. If you call Andy and her pussys out I could just meet you there

Ya I justdrove by the park and some of it was dry. I'm gonna drive there cause I have to get my daughter by 2. If you call Andy and her pussys out I could just meet you there

yeah. If you want the older one its a bit cheaper . Butthe only shop I know has them in stock is empire . The spindle on that one is 126 vs 106 for the GHD ti. But it only comes in the bmx spacing . but wow 224 + just for one part of the cranks. I would rather buy an XTR haha

Sooo much money for a part that has no guarantee of not breaking lol. they should be cheaper

Profile is weird . If you want something from them its better to buy it whole . Like a full ti elite hub. Then if it breakes they sell you the replacement part at an undisclosed price to you only . Same with the other parts . To buy it separate it cost a buttload . Does deity warrranty the ti spindle ? I know profile does not .

thats good to hear Now I can go ahaed and weight weenie my bike So did they explain the shipping and duties wave deal?

wow that took a while . So what did he say . Is it a good deal?

lol I hear ya. Well I would pass on the ti driver . they wear really fast . The boss less set up it great though for sure . I have never seen it offerered in a ti/no boss set up though. I have wondered if profile does not sell it like this because the spline drive setup might not work well with a ti spindle . The reagular profile is only 100g heavier than the ti. plus the no boss arms saves like another 20g+ Chosing 165 arms I know will also weigh a lot less. I would think on a regular setup it should come really close to a ti spindle set up for sure . But contact profile bout running the spline drive on a ti spindle to see what they have to say . Oh and tree runs 22 and 23 sprockets now so you can run a 9 or 8t profile driver if you wanted too. thats lighter than a 10 .

I think it means they would brown wrap it . Like a regular post so since its not a used service it will be considered personal post. China based stores do this all the time. So which profile crank set do you want . light or GHD

Dans is has sales every month. I ave the calender . so if you need info let me know . You could save 25 on a purchase over 100 . I have been looking into the premium spline drive set . Come s with a 25t spindle and arms 28oz total . 25oz for just the arms and spindle . I also have a link for gusset woodstocks spline dive cranks on sale for 150. the arms are 400g they dont say what the spindle is . I am guessing standard 270g

I still pester E for a chrome arm set though HAHAHAHA!!

Ya got me lol. The choice to run 48s again was smart though. Also that he made a stronger arm. I think it weighs more than the V2 but built stronger .

they were 4130's not vendetas and they were over two years old haha , I think it was a more than fair deal 50 I got two arms and spindle . I had issues with the maj though with chain line. had nothing to do with the deity setup. The frame was made for MTB cranks for sure because when I installed my siants it all lined up really well. On my friends park frame that has them now . With the spanish set up ot lined up a lot better . NS sometimes makes the frames strange

No reply. I talking to a guy in courtnay with a khs with 24's. He also has a Nordic havoc. The havoc is posted in street in courtnay

I sold the spindle But I still have the original 48 spline deity one. The drive side arm cracked, Eric did not have any replacements. He offered me a 38spline at low cost or a V3 with 10 off. I just got the 38 one and sold it to a local and decided to stay with the saints on the maj because they felt better .

To

Hey man how are those octane one rims holding?

I've seen those. Dan wants to buy a surly with tires like that

hey whats up

I like the price mostly, already have 3 frames (+2 bmx frames)

thanks

wheres the 24" penut?

that sucks! I didn't even get to oder mine lol. I was holding out for a responce from this kid that has a 175 profile with ti axle for 175 complete . I offered him 150 for the set up its new. It also comes with the 106g spindle empire has the same set up in two forms I think 204$ for the solid ti and 226 for the hollow ti

i will mail you the link. lol I know a lot of PB follows me now and it would sell out in a second haha